Mubychem Limited of USA is a pioneer manufacturers suppliers exporters & importers of chemicals including Hydraulic fracturing stimulation & oil well production chemicals, Pharmaceutical excipients, Fragrance & flavor chemicals. Muby Chem Ltd has several manufacturing facilities and toll manufacturers across the globe. We have offices warehouses and representatives in Houston & Midland Texas and Chicago Illinois USA. Our suppliers have accreditations like FDA - GMP approval, ISO-9001:2008, ISO-22000:2005 HACCP, Kosher & Halal Certification. We offer Commercial Pure Pharmacopoeia ACS AR Analytical Reagent & Food Grade of Chemicals and do Toll Manufacturing for oil well drilling fracking fracturing and others.
Methylthioninium Chloride BP Methylene Blue USP Manufacturers
MSDS of Methylthioninium Chloride Methylene Blue USP ManufacturersSpecifications of Methylene Blue are as follows:
Chemical Formula: C16H18N3CIS
Molecular Weight: 319.85 gm / mole
Chemical Name: 3,7-bis(Dimethylamino)-phenazathionium chloride Tetramethylthionine chloride
CAS Registration: 61-73-4
C.I No.: 52015
Appearance: Dark Green Crystalline Powder
Assay (as is basis): 80 % - 85%
Assay (on dry basis): 98% -101%
Loss on drying: 10% -20%
Solubility: Clear Blue Solution
Ash content: 1% Max
Residual Solvent: Nil
Aluminium: 100 ppm Max
Cadmium: 1ppm Max
Chromium: 10ppm Max
Copper: 50ppm Max
Tin: 10 ppm Max
Iron: 100ppm Max
Manganese: 10ppm Max
Molybdenum: 10ppm Max
Methylene Blue USP
Phenothiazin-5-ium, 3,7-bis(dimethylamino)-, chloride, trihydrate.
C.I. Basic Blue 9 trihydrate [7220-79-3]
Anhydrous 319.86 [61-73-4]
Methylene Blue contains not less than 98.0 percent and not more than 103.0 percent of C16H18ClN3S, calculated on the dried basis.
Identification: Infrared Absorption 197K .
Loss on drying— Dry it at 75 and at a pressure not exceeding 5 mm of mercury for 4 hours: it loses between 8.0% and 18.0% of its weight.
Residue on ignition: not more than 1.2%.
Arsenic— Prepare the Test Preparation by mixing 0.375 g with 10 mL of water in the arsine generator flask. Add 15 mL of nitric acid and 5 mL of perchloric acid, mix, and heat cautiously to the production of strong fumes of perchloric acid. Cool, wash down the sides of the flask with water, and again heat to strong fumes. Again cool, wash down the sides of the flask, and heat to fumes. Cool, dilute with water to 52 mL, and add 3 mL of hydrochloric acid: the resulting solution meets the requirements of the test, the addition of 20 mL of 7 N sulfuric acid specified for Procedure being omitted. The limit is 8 ppm.
Copper or zinc— Ignite 1.0 g in a porcelain crucible, using as low a temperature as practicable, until all of the carbon is oxidized. Cool the residue, add 15 mL of 2 N nitric acid, and boil for 5 minutes. Filter the cooled solution, and wash any residue with 10 mL of water. To the combined filtrate and washing add an excess of 6 N ammonium hydroxide, and filter the solution into a 50 mL volumetric flask. Wash the precipitate with small portions of water, adding the washings to the filtrate, dilute the solution with water to volume, and mix. To 25 mL of the solution add 10 mL of hydrogen sulfide TS: no turbidity is produced within 5 minutes (absence of zinc). Any dark color produced does not exceed that of a control prepared by boiling a quantity of cupric sulfate, equivalent to 200 @g of copper, with 15 mL of 2 N nitric acid for 5 minutes and by treating this solution as directed above, beginning with “Filter the cooled solution” (0.02% of copper).
Chromatographic purity— Quantitatively dissolve an accurately weighed quantity of Methylene Blue in methanol to obtain a Test solution containing 1.0 mg per mL Dissolve a suitable quantity of USP Methylene Blue RS in methanol to obtain a Standard solution having a concentration of 100 @g per mL. Quantitatively dilute a portion of this solution with methanol to obtain a Diluted standard solution having a concentration of 10 @g per mL. Apply 5 @L each of the Test solution, the Standard solution, and the Diluted standard solution to a suitable thin-layer chromatographic plate coated with a 0.25-mm layer of octadecylsilanized chromatographic silica gel. Allow the spots to dry, and develop the chromatogram in a chromatographic chamber with a solvent system consisting of a mixture of the upper layer separated from a well-shaken mixture of water, n-butanol, and glacial acetic acid (100:80:20), until the solvent front has moved about three-fourths of the length of the plate. Remove the plate from the chamber, allow the solvent to evaporate, and visually locate the spots on the plate: the RF value of the principal spot in the chromatogram from the Test solution corresponds to that from the Standard solution, and other spots, if present in the chromatogram from the Test solution, consist of a secondary spot that does not exceed in size or intensity, the principal spot obtained from the Standard solution (10%), and not more than two additional spots, neither of which exceeds in size or intensity the principal spot from the Diluted standard solution (1%)Assay— Transfer about 100 mg of Methylene Blue, accurately weighed, to a 250-mL volumetric flask, dissolve in and dilute with diluted alcohol to volume, and mix. Transfer 5.0 mL of this solution to a 100-mL volumetric flask, dilute with diluted alcohol to volume, and mix. Transfer 5.0 mL of this solution to a 50-mL volumetric flask, dilute with diluted alcohol to volume, and mix. This solution contains about 2 @g per mL. Dissolve an accurately weighed quantity of USP Methylene Blue RS in diluted alcohol, and dilute quantitatively and stepwise with diluted alcohol to obtain a Standard solution having a known concentration of about 2 @g per mL. Concomitantly determine the absorbance of both solutions in 1-cm cells at the wavelength of maximum absorbance at about 663 nm, with a suitable spectrophotometer, using diluted alcohol as the blank. Calculate the quantity, in mg, of C16H18ClN3S in the Methylene Blue taken by the formula:
50C(AU / AS)
in which C is the concentration, in @g per mL, of anhydrous methylene blue in the Standard solution; and AU and AS are the absorbance of the solution of Methylene Blue and the Standard solution, respectively.
Methylthioninium Chloride BP or Methylthioninium Chloride Ph. Eur is also offered.
IUPAC name is 3,7-Bis(dimethylamino)phenothiazin-5-ylium chloride or 3,7-bis(Dimethylamino)-phenothiazin-5-ium chloride
Methylene Blue USP Manufacturers
Methylthioninium Chloride Manufacturers
Muby Chem Ltd.
Toll manufacturing & Warehouse at Houston Beasley & Midland, Texas, USA
USA, Canada, Mexico Customers may e-mail: email@example.com
Europe Africa Asia India Mumbai e-mail: firstname.lastname@example.org
Exporters Importers between USA Canada UAE Europe South Africa Tanzania Kenya Uganda Egypt Nigeria Turkey Mexico Brazil Argentina Chile Dubai China India etc.
26 June, 2015. Copyright and Usual Disclaimer is Applicable.
Best Selling IP BP USP FCC ACS Grades of Chemicals by Anmol Chemicals
Chemical Products offered ex-stock. Any quantity. Container loads to pallets or packs
Other Ex-stock Chemicals Offered
Ammonium Chloride with/without anti caking agent Crystals & Granules
Ammonium Persulfate oxidizing gel breaker
Calcium Nitrite Crystals & 30% Solution Calcium Nitrate
Ceric Ammonium Nitrate
Magnesium Chloride Anhydrous & Hexahydrate FCC USP
Magnesium Sulfate Anhydrous & Heptahydrate
Polycarboxylate Super plasticizer, Water Reducer Concrete Strengthener
Sodium Acetate Anhydrous & Trihydrate crystals & granular
Sodium Formaldehyde Bisulfite
Sodium Nitrite Nitrate Crystals & Solution
Sodium Thiosulfate FCC Anhydrous & Pentahydrate Photographic
Zinc Chloride Anhydrous & Liquid Solution 62.5%, 67% 70%
Zinc Ammonium Chloride Galvanizing Flux Powder Nuggets, & Liquid Solution-
Acid Inhibitor cum Fume Suppressant & Flux Enhancer
If you feed a dog with your hand, it will never bite you. That is the principal difference between a dog and a man.
Methylene Blue is also called ( CAS No. 548-62-9; 603-47-4 )
Basic blue 9 (C.I. 52015)
Solvent blue 8 (C.I. 52015)